Dock Norte S.A. Equipamiento y Servicios de Monitoreo Ambiental

Vea esta pagina en español

Brochure

Download brochure

Different Scenarios

Download Different Scenarios Setup

Keep your software updated

Download Update

LNX Connector is a secure real time remote control software which enables you to work on a remote LNX Series DataLOGGER as if you were using its own keyboard and mouse.
LNX Connector uses TCP/IP omnipresent protocol, the more extended and used protocol on LAN, WAN and Internet. It means, you’ll be able to access your LNX Series DataLOGGER from anywhere in the world. LNX Connector is very easy to learn and use. This is because of its simplicity. This software it’s designed to run in Microsoft Windows OS.

There are three connection modes:

• Support
• ReadOnly
• FullControl

Support
This mode can be divided in two dections, Messages and Board, in Message section it’ll be showing the messages that LNX Series DataLOGGER send to you and the messages that you sent to it. Also from this section is where you’ll be writing the messages.

In Board is the area where you’ll be able to draw, each one have a particular color for differentiate as you can see in the image.
There is a button that is the option to draw a straight line by clicking and dragging. There is a button that is for make hand draw with the mouse. And there is a button that allows you to clear the board and start again, only clear your board not the LNX Series DataLOGGER board.

ReadOnly
In this mode, you’re not able to do anything but watch what’s happening with the LNX Series DataLOGGER in real time.

FullControl
In this mode, you get total control of the LNX Series DataLOGGER. You are able to configure every alarm, sensor, or even the system setup. Also you can calibrate any calibrable sensor, just clicking the Start button (This button only appears if the sensor is calibrable).

Security
LNX Series DataLOGGER auto detects external connections. For security reasons, when some external connection is made, the following screen is displayed. To disconnect it immediately and get total control again, you just input the keyword “000” (three zeros) and press Enter.


SOFTWARE


LNX Connector
Vea esta pagina en español Brochure Download brochure Different Scenarios Download Different Scenarios Setup Keep your software updated Download Update LNX Connector is a secure real time remote control software which enables you to work on a remote LNX Series DataLOGGER as if you were using its own keyboard and mouse. LNX Connector uses TCP/IP omnipresent protocol, the more extended and used protocol on LAN, WAN and Internet. It means, you’ll be able to access your LNX Series DataLOGGER from anywhere in the world. LNX Connector is very easy to learn and use. This is because of its simplicity. This software it’s designed to run in Microsoft Windows OS. There are three connection modes: • Support • ReadOnly • FullControl Support This mode can be divided in two dections, Messages and Board, in Message section it’ll be showing the messages that LNX Series DataLOGGER send to you and the messages that you sent to it. Also from this section is where you’ll be writing the messages. In Board is the area where you’ll be able to draw, each one have a particular color for differentiate as you can see in the image. There is a button that is the option to draw a straight line by clicking and dragging. There is a button that is for make hand draw with the mouse. And there is a button that allows you to clear the board and start again, only clear your board not the LNX Series DataLOGGER board. ReadOnly In this mode, you’re not able to do anything but watch what’s happening with the LNX Series DataLOGGER in real time. FullControl In this mode, you get total control of the LNX Series DataLOGGER. You are able to configure every alarm, sensor, or even the system setup. Also you can calibrate any calibrable sensor, just clicking the Start button (This button only appears if the sensor is calibrable). Security LNX Series DataLOGGER auto detects external connections. For security reasons, when some external connection is made, the following screen is displayed. To disconnect it immediately and get total control again, you just input the keyword “000” (three zeros) and press Enter.